#Xbox 360 s power cord how to

However, it also means I need to find a suitable power supply that can output at least 4.6A at ~23.1V with an input range of 11 to 15V. The obvious solution was to purchase new charging equipment like this beautiful Turnigy 8s charger capable of 7A continuous. That is great except my Triton EQ charger can only handle 6s Lithium anything. Just match the colors together and ignore the grey wire as it isn't needed for normal power functions.My most recent scooter (that I built and haven't yet blogged about) uses a 7s2p Lithium Iron Phosphate pack using A123 cells. I'll do some more testing on different wiring configurations at a later date but it's really pretty basic. I have a ton of supplies laying around because I run a computer shop and we repair game consoles. As long as you don't mix up the colors you should be fine. It's going to be difficult to cause any damage to the console by trying that. In that case just leave the extra one out. I'm sure it would work perfectly fine if you are more comfortable going one to one with the connections. I soldered all three yellow directly together with the two yellow on the slim and the same for the black. Since all three of the yellow wires are 12v and all three of the black are ground there is no harm in connecting three wires to two wires.

The slim seems to be engineered to use only two separate inputs for power. They split the power off three ways for three independent pin sets in the original connector. The reason there are three wires in the old supply is mainly due to the way the power was routed into the original style of motherboard. The slim is working perfectly with the adapted supply. This should work for any of the original supplies. Microsoft obviously won't honor a warranty if they know you've done this. If all goes well you should have a working original PSU on a slim XBOX.ДЄgain, this is AT YOUR OWN RISK. Plug the PSU into the XBOX and power it up. You'll want to verify that the light on the PSU does light up to indicate standby power without any shorts. IF YOU DO NOT TAPE THEM PROPERLY YOU WILL RUIN YOUR PSU.ДЄfter all connections are made and taped, test the PSU by plugging it in, but DO NOT plug it into the xbox yet.

DO THIS AT YOUR OWN RISK!!!!Д«E SURE TO TAPE EACH CONNECTION WITH ELECTRICAL TAPE TO PREVENT A SHORT. It is not required for the XBOX to function normally. You can easily 'convert' an original supply (I used a 150W Supply) by connecting the matching colors except for the grey wire. One Grey (? - Could be communication between XBOX and PSU) The wiring from the two plugs is as below: I didn't see the point in purchasing a replacement since I had a few from the older systems laying around. I just recently did this when my slim PSU failed. Opened it up again and no dust, it must me beyond repairing at this point, since it hasn't got nice treatment since it broke haha. It fixed the problem for a few weeks, but then happened again. I once opened the brick and cleared out a whole lot of dust. Thanks dudes, getting tired of it shutting down so soon. Wiring Method To Power New Elite Xbox 360 With Atx Supply - Scenyx Entertainment Community

#Xbox 360 s power cord how to

Here is some info on how to use an ATX power supply to run your slim xbox, if it helps at all. If anybody has some info on this it would be appriciated. The slim brick seems to have two yellow ones, two black ones, one grey, one red and one blueДo you think it's okay to wire it up in a way that i just leave out the one extra yellow and one extra black wire and tape them so they won't touch anything? The old brick seems to have three yellow wires, three black ones, one grey/white one and one blue. Haven't found any advice online on how you would do this by yourself, and don't want to mess up my xbox. 15-30 minutes, and they don't send this transfer adapter to my country:/ Do you think it's safe to cut the wire on my fat myself and somehow find a way to re-connect it with the head of the slim adapter wire (the one that actually connects to the back of the slim)